In this paper, we propose a preemptive priority handoff scheme for integrated voice/data cellular mobile systems. In our scheme, calls are divided into three different classes: handoff voice calls, originating voice calls, and data calls. In each cell of the system there is a queue only for data calls. Priority is given to handoff voice calls over the other two kinds of calls. That is, the right to preempt the service of data is given to a handoff voice call if on arrival it finds no idle channels. The interrupted data call returns to the queue. The system is modeled by a two-dimensional Markov chain. We apply the Successive Over-Relaxation (SOR) method to obtain the equilibrium state probabilities. Blocking and forced termination probabilities for voice calls are obtained. Moreover, average queue length and average transmission delay of data calls are evaluated. The results are compared with another handoff scheme for integrated voice/data cellular mobile systems where some numbers of channels are reserved for voice handoff calls. It is shown that, when the data traffic is not very light, the new scheme can provide lower blocking probability for originating voice calls, lower forced termination probability for ongoing voice calls, and shorter average queue length and less average transmission delay for data calls.

A clock recovery circuit is a key component in optical communication systems. In this paper, an optoelectronic clock recovery circuit is reported that monolithically integrates a resonant tunneling diode (RTD) and a uni-traveling-carrier photodiode (UTC-PD). The circuit is an injection-locked-type RTD oscillator that uses the photo-current generated by the UTC-PD. Fundamental and sub-harmonic clock extraction is confirmed for the first time with good clock recovery circuit characteristics. The IC extracts an electrical 11.55-GHz clock signal from 11.55-Gbit/s RZ optical data streams with the wide locking range of 450 MHz and low power dissipation of 1.3 mW. Furthermore, the extraction of a sub-harmonic clock from 23.1-Gbit/s and 46.2-Gbit/s input data streams is also confirmed in the wider locking range of 600 MHz. The RMS jitter as determined from a single sideband phase noise measurement is extremely low at less than 200 fs in both cases of clock and sub-harmonic clock extraction. To our knowledge, the product of the output power and operating frequency of the circuit is the highest ever reported for injection-locked-type RTD oscillators. These characteristics indicate the feasibility of the optoelectronic clock recovery circuit for use in future ultra-high-speed fully monolithic receivers.

A clock recovery circuit is a key component in optical communication systems. In this paper, an optoelectronic clock recovery circuit is reported that monolithically integrates a resonant tunneling diode (RTD) and a uni-traveling-carrier photodiode (UTC-PD). The circuit is an injection-locked-type RTD oscillator that uses the photo-current generated by the UTC-PD. Fundamental and sub-harmonic clock extraction is confirmed for the first time with good clock recovery circuit characteristics. The IC extracts an electrical 11.55-GHz clock signal from 11.55-Gbit/s RZ optical data streams with the wide locking range of 450 MHz and low power dissipation of 1.3 mW. Furthermore, the extraction of a sub-harmonic clock from 23.1-Gbit/s and 46.2-Gbit/s input data streams is also confirmed in the wider locking range of 600 MHz. The RMS jitter as determined from a single sideband phase noise measurement is extremely low at less than 200 fs in both cases of clock and sub-harmonic clock extraction. To our knowledge, the product of the output power and operating frequency of the circuit is the highest ever reported for injection-locked-type RTD oscillators. These characteristics indicate the feasibility of the optoelectronic clock recovery circuit for use in future ultra-high-speed fully monolithic receivers.

The microwave attenuation, which is the key factor for realizing very large bandwidths Ti:LiNbO3 optical modulators is fully studied and the causes and reduction techniques are discussed in detail. Practical realization of wide-band optical modulators with low microwave attenuation and low driving voltage is also discussed.

In this paper, we consider conventional signaling link fault tolerance and error correction mechanisms to provide reliable services of mobile multimedia telecommunication network based on ATM (Asynchronous Transfer Mode) technology. Also, we propose an efficient signaling protocol interworking architecture and a reliable distributed interworking network architecture between SS7 based FPLMTS and ATM networks. Besides, we evaluate the performance of proposed method through computer simulation. According to the results, proposed signaling architecture shows efficient and fast fault restoration characteristics than conventional MTP-3/3b based network. Functional signaling protocol stack and network architecture of proposed fast rerouting mechanism provide reliable and efficient restoration performance in view of interworking between SS7 based FPLMTS and ATM networks.

The use of existing metallic local line facilities is being studied for the provision of high-speed digital transmission services. Local line characteristics have to be modeled in the form of the objective requirements that should be met by DSL for estimating the feasibility of the service provision in the actual network. This paper presents the results of a study that models the metallic media characteristics of NTT's local network. First, the line lenghts determined by the existing local line deployment rule and the cable types used in the networks are introduced. Second, the values of crosstalk characteristics, the most significant factors in limiting DSL range, are given by classifying essential line conditioning states of each cable. The values of crosstalk characteristics are newly computed by taking into account detailed cable pair-binding (cabling) structures, and the worst case values among all possible combinations of multiple inter-pair interfering-interfered relationships within a cable are given though a previous study approximated cable pair-binding structures. The crosstalk characteristics of NTT's and American local networks are also compared. A modified approximate equation of line propagation characteristics is also proposed for representative local lines, and its precision is verified by comparing simulation results to actual measurements in both frequency and time domains.

This paper proposes a novel Doppler frequency shift compensation technique to achieve terrestrial and low earth orbit (LEO) satellite dual mode DS/CDMA terminals robust to high Doppler shift and multipath fading. In order to satisfy the requirements of wide dynamic range and high accuracy simultaneously, the proposed scheme employs two stage compensation scheme, i.e., coarse compensation to keep dynamic range of about 100 kHz and fine compensation to satisfy its resolution of about 30 Hz, using block demodulation technique. Computer simulation results show that the proposed scheme can sufficiently compensate for the offset frequency up to the range of about 100 kHz at the terrestrial and LEO satellite combined mobile communication systems.

In this study, we analyze the system which simultaneously transmits spread-spectrum signals with different processing gains. The main purpose of this study is to give an analytical framework that describes the influence of the interfering signals with different processing gains. For this purpose, we define a crosscorrelation function between the spreading sequences with different code lengths, and discuss the effects of interaction between the signals. As the results, we show that the power of the interference component after despreading procedure, the power ratio of the desired to undesired components, and thus the bit error rate are not constant but vary symbol by symbol.

Personal communication systems (PCS) have more signalling traffic than conventional fixed networks and require large-scale databases to manage users' profiles, which are sets of data items, such as the location the user is currently visiting and the user's authentication key, necessary for a PCS user to be provided with PCS services. This paper focuses on inter-network roaming in PCS environments. In designing a PCS supporting roaming service, it is essential to avoid increased signalling traffic and data searching time in the database. We first identify the appropriate domains for three routing schemes-Direction Routing, Redirection Routing, and Look-ahead Routing-from the viewpoints of the number of signals for inter-network roaming and roaming probability. We do this for two kinds of PCS database network architecture, Home Location Register (HLR) and Visitor Location Register (VLR), and show that Look-ahead Routing is the best scheme for the HLR network architecture (considering the number of signals for intra-network and inter-network database access) and that in the VLR network architecture, the decreasing of the roaming probability expands domains for which Redirection Routing is appropriate. We also propose a generic PCS data model that inter-network roaming interfaces can use to search effectively for a user's profile. The data model clarifies the contents of a set of data items which share certain characteristics, data items that the contents compose, and the relationships (data structures) between sets of data items. The model is based on the X. 500 series recommendations, which are applied for an Intelligent Network. We also propose a data structure between sets of data items using the directory information tree and show the ASN. 1 notations of the data model.

In order to pave the way to B-ISDN, one of the most important issues for network providers is to identify the most efficient B-ISDN introduction strategy. This paper focuses on the costs of introducing ATM transmission systems into backbone transport networks which must provide highly reliable broad band transmission capability. In this context, the main rival to ATM is Synchronous Transfer Mode (STM); recent Synchronous Digital Hierarchy (SDH) equipment supports the establishment of advanced STM-based high speed transport networks. This paper offers a cost comparison of ATM and STM based backbone transport networks. A digital path network in STM has a hierarchical structure determined by the hierarchical multiplexing scheme employed. The minimum cost STM path network can only be determined by developing a path design method that considers all hierarchical path levels and yields the optimum balance of link cost and node cost. Virtual paths have desirable features such as non-deterministic path bandwidth and non-hierarchical and direct multiplexing capability into high speed optical transmission links. These features make it possible to implement a non-hierarchical VP network with ATM cross connect systems which can handle any bandwidth VP with a universal cell switching function. This paper shows that the non-hierarchical VP routing, which strongly minimizes link cost, can be implemented without significantly increasing node cost. Network design simulations show that the virtual path scheme, possible only in an ATM network, yields the most cost effective path network configuration.

External modulators, which have smaller chirping characteristics than laser diode direct modulation, are desired for high-speed and long-distance optical fiber communication systems. This paper reviews semiconductor and Ti:LiNbO3 guided-wave high-speed optical modulators. Since several effects exist for semiconductor materials, various kinds of semiconductor optical modulators have been investigated. Among these, absorption type intensity modulators based on Franz-Keldysh effect in bulk materials and quantum confined stark effect in multiple quantum well materials, are promising because of compactness, low drive voltage nature and integration ease with DFB lasers. Recent progress on semiconductor absorption modulators and DFB-LD integrated semiconductor modulators is discussed with emphasis on a novel fabrication method using selective area growth by MOVPE (Metal Organic Vapor Phase Epitaxy). The Ti:LiNbO3 optical modulators are also important, due to the advantage of superior chirping characteristics and wide bandwidth. Since the Ti:LiNbO3 optical modulator has low propagation loss and low conductor loss natures for optical waves and microwaves, respectively, the traveling-wave electrode configuration is suitable for high-speed operation. Here, broadband Ti:LiNbO3 optical modulators are discussed with emphasis on traveling-wave electrode design.

The use of existing metallic local line facilities is being studied for providing "video on demand (VOD)" services to residential subscribers across asymmetric digital subscriber lines (ADSL). ADSL carries a high-rate channel in the downstream direction from a central office (CO) to the subscriber, and a low-rate channel in both directions on an existing 2-wire pair. Audio and video signals are compressed by the moving picture experts group's standardized algorithms (MPEG 1 and MPEG 2), and delivered to the subscriber in the high-rate channel. Control (demand and response) signals are transceived in the low-rate channel. This paper presents the line length coverage of ADSL systems given the environment of NTT's local networks. The bit rates in the downstream and upstream directions are assumed to be 1.6-9.2Mbit/s and 24kbit/s, respectively. Two types of ADSL systems are considered: transceiving ADSL signals using the plain old telephone service (POTS) line or the basic rate access (BRA; 320 kbaud ping-pong transmission system) line on the same 2-wire pair. 16-QAM, 32-QAM and 64-QAM are compared as transmission schemes. Intra-system crosstalk interference (interference between identical transmission systems) and inter-system crosstalk interference (interference between different transmission systems) with the existing digital subscriber lines (DSL) are estimated. It is shown that the inter-system crosstalk interference with BRA is most stringent, and ADSL with 16-QAM yields the best performance in NTT's local networks. This paper concludes that realizing ADSL with 16-QAM can achieve channel capacities of up to 9.2Mbit/s for fiber-in-the-feeder (FITF) access systems, but the possibility of applying ADSL to direct access systems is remote except for a restricted short haul use. Some comparisons regarding American local networks are also described.

In this paper, we evaluate the performance of handoff schemes in microcellular personal communication systems (PCS) which cater to both pedestrian and vehicular users. Various performance parameters, including blocking of new calls,channel utilization, handoff blocking and call termination probabilities for each user type are evaluated. We study different queuing disciplines for handoff calls and their impact on system performance. We also study the tradeoff in handoff blocking and call termination probabilities between user types as the handoff traffic carried by the system from each user type is varied.

This paper presents a newly developed analytical method which evaluates the virtual path bandwidth control effects for a general topology ATM (Asynchronous Transfer Mode) transport network. The virtual path concept can enhance the controllability of path bandwidth. Required link capacity to attain a specified call blocking probability can be reduced by applying virtual path bandwidth control. This paper proposes an analytical method to evaluate the call blocking probability of a general topology ATM network, which includes many virtual paths, that is using virtual path bandwidth control. A method for the designing link capacities of the network is also proposed. These methods make it possible to design an optimum transport network with path bandwidth control. Finally, a newly developed approximation technique is used to develop some analytical results on the effects of dynamic path bandwidth control are provided to demonstrate its effectiveness.

In this paper, we demonstrate how Yamakawa's chaotic chips and Chua's circuits can be used to implement a secure communication system. Furthermore, their performance for the secure communication is discussed.

A system for measuring the low frequency amplitude and phase noises was set-up, with employing a phase sensitive detector and phase-shifter. It is noted that both noises were partly correlated. The phase noise was explained by the transit time fluctuation due to the fluctuating diffusion coefficient. The amplitude noise reduction was demonstrated by applying the inverted output of the phase noise to the amplitude noise.

Long term phase noises are characterized for network synchronization using two time domain measurement techniques: the Maximum Time Interval Error (MTIE) and Time Variance (TVAR). First, the characteristics of previously measured fiber delay variations are evaluated. The diurnal and annual delay variations and the long term noise feature of random walk phase modulation are well represented by the TVAR technique. The delay variation due to the AU pointer operation is then measured using commercial SDH demultiplexing equipment and compared with the simulation result; the simulation result agrees well with the experimental result. The delay variation in the SDH equipment is simulated using the thermal fiber delay variation measured in the actual network as the input phase of the equipment. It is shown that the SDH equipment sometimes generates delay steps of 617ns, which are larger than the normal pointer operations of 154ns. The long term delay variation, periods over 107s, due to the threshold spacing between the positive and negative stuffing is described. We also show that TVAR is suitable for evaluating the phase noise feature and MTIE can clearly show the peak value of phase noise. The long term phase noises evaluated in this paper are the dominant sources that degrade network synchronous performance. The results of this paper will be useful in designing the equipment synchronous specification.

This paper presents the results of a study made to determine the line length coverage of the high-bit-rate digital subscriber line (HDSL) present in NTT's local networks. The HDSL carries one bi-directional 784 kbit/s channel per pair and supports the digital interface at 1544kbit/s by using two cable pairs. The primary purpose of this study is to estimate the range limits for candidate transmission schemes considering line installation conditions, and to determine the most promising transmission scheme and its feasibility given the environment of NTT's local networks. Pulse amplitude modulation (PAM) and quadrature amplitude modulation (QAM) transmission schemes are compared for HDSL implementation. It is shown that 2B1Q-PAM and 16-QAM generally achieve better performance than the more complicated PAM and QAM given the presence intra-system crosstalk interference (interference between identical transmission systems). The range limits determined by inter-system crosstalk interference (interference between different transmission systems) with basic rate access (BRA) implementing a burst-mode transmission method are also estimated. This paper concludes that 2B1Q-PAM achieves the best overall performance in NTT's local networks. A feasibility study of 192-6144 kbit/s transmission is also described.

An Ultra-high-speed (higher than 60 MHz) Viterbi decoder VLSIC with coding rates from one-half to fifteen-sixteenth and a constraint length of seven for forward error correction (FEC) has been developed using 0.8-µm semicustom CMOS LSIC technology and a newly developed high-speed ACS circuit. To reduce power consumption of the one-chip Viterbi decoder, a universal-coding-rate scarce-state-transition (SST) Viterbi decoding scheme and low-power-consumption burst-mode-selection (BMS) path memory have been proposed and employed to the developed VLSIC. In addition, a new maximum-likelihood-decision (MLD) circuit for the SST Viterbi decoder has been developed. The total power consumption of the developed chip is reduced to 75% of the conventional one and the developed Viterbi decodar VLSIC achieves a maximum operation speed of 60 MHz. It achieves near theoretical net coding-gain performance for various coding rates.

ISO and ITU-T have developed the standard concept of the Telecommunications Management Network (TMN). This standard does not, however, specify interface implementation. The user requires an Application Programming Interface (API) that bridges user application and the TMN concept to construct a TMN-based application. This paper proposes an object oriented API (OOAPI) that is suitable for TMN-based operations system implementation. OOAPI is one interface of the Common Management Information Service Element (CMISE), and uses the Common Management Information Protocol (CMIP). OOAPI is composed of two C++ programming language constructs: Data Object and Interface object "M_User". The Data Object makes it easier for the user to access management information. The M_User provides a connection-less CMISE interface because the OOAPI handles CMIP association automatically. The M_User also provides MO location-transparency by using the OSI Directory Service. This paper compares the existing MO location-transparency schemes with the OOAPI method, and clarifies the advantages of OOAPI. This paper also indicates results from OOAPI trials, and confirms that OOAPI has sufficient performance to implement highly effective TMN operations system.